Opleiding: Certified Data Center Specialist - CDCS (incl. examen) - Hercertificering (2024)

Lesmethode :

Klassikaal

Algemeen :

Doel :

De ontwerp life cycle van een Datacenter, en de fases daarin, begrijpen
Vereisten gedetailleerd bespreken met suppliers, vendors en anderen
Ontwerpplannen beoordelen op technisch vlak
Tier-levels begrijpen, zowel voor design/setup als voor onderhoud
Overwegingen rondom het gebouw begrijpen, zoals brandbestendigheid, thermische en seismische stabiliteit
Begrijpen hoe een verhoogde vloer bepaalde problemen kan oplossen en voorkomen
Een Single Line Electrical Diagram lezen
De juiste UPS en parallelle configuratie kiezen
Accucapaciteiten berekenen en zeker weten dat dit voldoet aan de vereisten
Bepalen hoe wordt voldaan aan eisen rond electromagnetische velden en mogelijke storing van apparaten
Fundamentele koeling opzetten en CFM, Delta-T en andere factoren begrijpen
Installaties beoordelen op brandbestrijding
Energie-efficiëntie meten en verbeteren

Doelgroep :

IT- en facility professionals die in en om een Data Center werken en verantwoordelijkheid dragen met betrekking tot het beheer en de beschikbaarheid van een Data Center.

Voorkennis :

Een goede passieve beheersing van de Engelse taal.
Deelnemers moeten voorafgaand aan deze training de Certified Datacenter Professional (CDCP) training gevolgd hebben en het CDCP examen met succes hebben afgerond.
En de volgende cursussen:

• Certified Data Center Professional - CDCP® (incl. examen)

Onderwerpen :

- Datacenter Design / Life Cycle Overview
- Overview of the phases of a Datacenter life cycle
- Planning, re-alignment and continuous improvement
- Tier Levels
- History of 'tier level' definitions
- Tier level definitions, categories and measure points
- Redundancy options
- Tiered Infrastructure Maintenance Standards (TIMS)
- Overwegingen en standaarden met betrekking tot gebouwen
- Floor loading requirements
- Fire rating for walls and glass
- Blast protection
- Bullet proofing
- Forced entry protection
- Verhoogde vloeren en verlaagde plafonds (advanced)
- Raised floor installation guidelines to ensure contractors
- install a proper closed and levelled raised access floor
- Choosing the right tiles and their locations
- Seismic mitigating floor constructions
- Choosing the correct suspended ceiling
- Geavanceerde stroomvoorziening
- Formulas which you should know for the Datacenter
- Single Line Electrical diagrams; how to read to ensure key components are present for protection
- Over current protection devices (MCB/MCCB/VCB/ACB/Fuses) definitions and what to use where
- Earth Leakage devices (RCB/RCD/ELCB/GFCI/ALCI/RCBO), definitions and what to use where
- Lightning strikes and surge protection devices (TVSS/SPD), how they operate, where to use and how to install
- Power cabling and cable run considerations
- PDU/DB setup and minimum requirements
- Generator component make up
- Choosing the required device
- Calculate required fuel storage tank capacity
- Paralleling of gen-sets
- Regulatory requirements
- Required specifications for UPS systems
- How to read data sheets and select the correct UPS
- Requirements for parallel configurations and avoid pitfalls such as single point of failures
- How parallel installation should be done, classic mistakes made by installers and how to avoid these
- Harmonic Filters
- Type of filters available and which one to select depending on the application
- Designing battery banks, how to calculate, and double check the battery bank to be installed
- Battery charging pitfalls and ensuring the right charger is being installed and used
- Using parallel battery banks; how to properly install them, limitations and risk when using batteries in parallel
- How to test batteries correctly and make decisions on cell/block or string replacement
- Battery casing choices; ABS, V0, V1, V2
- Alternative energy storage; flywheel, re-useable cell etc.
- Electromagnetische velden (advanced)
- Differences between single, three phase and bus-bar EMF
- Options available to measure EMF and how to interpret the results from single axe and composite measurements
- Guidance on safe distance for equipment and human
- Calculation of EMF attenuation factor for shielding material permeability and saturation factors
- Geavanceerde koeling
- Environmental class definitions and thermal specifications
- Equipment airflow and Delta-T definitions and limits
- Planning for floor, rack and cooling equipment
- CFM requirement calculations and conversions
- Air-conditioner specifications and how to select the correct air-conditioner with the required capacity and flow
- Techniques for optimization of air flow
- Redundancy guidelines for air-conditioners avoiding classic misconceptions
- Liquid cooling guidelines for Datacenters
- Geavanceerde brandbeveiliging
- Fire triangle and elements to stop a fire
- Detection systems in detail (VESDA, VIEW, Smoke sensors)
- Considerations for installation of sensors
- Difference in water based systems i.e. dry-pipe, pre-action and why most of them don't work and how to detect this
- Details on Inert, Halocarbon, fluorinated systems